Contact Person : Tina Fu
Phone Number : +86 755-27806536
WhatsApp : +8615919862398
May 20, 2021
TFT LCD Display for customized live broadcast platform for customers
| MODEL | CH430WV15A-CT |
深圳市诚皓光电有限公司 Shenzhen Chenghao OptoeLectRonic Co.,Ltd |
|||||||||
|
DEAWING |
--- ----- --- | ||||||||||
| CHECK | |||||||||||
| VO | NEW | 2018.10.23 | APPROVE | DATE | PAGE | 1 OF 1 | UMIT | mm | |||
| REV | CONTENT | TOLERANCE | -- --- ---- | ||||||||
1.TFT General Information:
| ITEM | STANDARD VALUES | UNITS |
| LCD type | 4.3’’TFT+CTP | -- |
| Dot arrangement | 480×(RGB)×800 | dots |
| Color filter array | RGB vertical stripe | -- |
| Display mode | IPS/ Transmissive/ NormallyBlack | -- |
| Viewing Direction | ALL | -- |
| TFTDriver IC | NT35510 | -- |
| CTPtype | G+F+F | -- |
| Surface Treatment | 6H | -- |
| CTP Driver IC | GT911 | -- |
| Module size | --(W)×113.9(H)×3.35(T) | -- |
| TFT/CTPActive area | 56.16(W)×93.6(H) | -- |
| Dotpitch | 0.117(W)×0.117(H) | -- |
| Interface | 2 lane-MIPI DSI | -- |
| Operating temperature | -- | -- |
| Storagetemperature | -- | -- |
| Back Light | --White LED in serial | -- |
| Weight | TBD | -- |
2.ExternalDimensions:
NOTES:
1.DISPLAY TYPE: 4.3" TFT
2.VIEWING DIRECTION: 80/80/80/80(U/D/L/R @ CR>10)
3.LCD DRIVE IC: NT35510
4.POLARIZER MODE: TRANSMISSIVE/POSITIVE
5.OPERATING TEMP: ****
6.STORAGE TEMP: ****
7.UNMARKER TOLERANCE: ****
8.REQUIREMENTS ON ENVIRONMENTAL PROTECTION: RoHS
CTP NOTE：
1.LENS+ITO Film+ITO Film+FPC+adhesive
LENS GLASS: **mm
SENSOR FILM: **mm
IC: GT911
2.Operation Voltage：**V-** V
3.Transmittance：≥**％
4.The cover hardness：**H
3.Interface Description
| PIN NO. |
SYMBOL | DESCRIPTION |
|
1 |
LEDA | Power for LED backlight (Anode). |
| 2 | LEDK | Power for LED backlight (Cathode). |
| 3 | VCI | A supply voltage to the analog circuit. |
| 4 | IOVCC | A supply voltage to the logic circuit. |
| 5 | /RESET | Reset input pin, Active “L”. |
| 6 | LEDPWM | Used for turning On/Off external LED backlight control. |
| 7 | GND | Power ground. |
| 8 | MIPI_D1P | MIPI-DSI data Lane 1 positive-end input pin |
| 9 | MIPI_D1N | MIPI-DSI data Lane 1 negative-end input pin |
| 10 | GND | Power ground |
| 11 | MIPI_CLKP | MIPI-DSI clock Lane positive-end input pin |
| 12 | MIPI_CLKN | MIPI-DSI clock Lane negative-end input pin |
| 13 | GND | Power ground |
| 14 | MIPI_D0P | MIPI-DSI data Lane 0 positive-end input pin |
| 15 | MIPI_D0N | MIPI-DSI data Lane 0 negative-end input pin |
| 16 | GND | Power ground |
| 17 | TE | Tearing effect output pin to synchronize MCU to frame writing, activated by S/W command. When this pin is not activated, this pin is output low. |
| 18 | GND | Power ground |
| 19 | NC | NC. |
| 20 | NC | NC |
| PIN NO. | SYMBOL | DESCRIPTION |
| 1 | VDD | Digital Power. |
| 2 | RST | Reset pin. Active low to enter reset state. |
| 3 | INT | Interruption signal. |
| 4 | NC | NC. |
| 5 | NC | NC. |
| 6 | SCL | I2C_clock. |
| 7 | SDA | I2C_data. |
| 8 | GND | Power ground. |
4.Optical Characteristics
The test of Optical specifications shall be measured in a dark room (ambient luminance 1luxand temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer system and TOPCON BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0. The center of the measuring spot on the Display surface shall stay fixed
Figure 1. The definition of Vth & Vsat
Figure 2. Measurement Set Up
Figure 3. Response Time Testing
5.Handling Precautions
Mounting method
The LCD panel of CH LCD module consists of two thin glass plates with polarizes which
easily be damaged. And since the module in so constructed as to be fixed by utilizing fitting holes
in the printed circuit board.
Extreme care should be needed when handling the LCD modules.
6.Packing Method
| MODEL NO. | CH430WV15A-CT |
| Module type | 4.3"TFT + CTP |
| Display Mode | IPS / Transmissive / Normally Black |
| CTP type | G+F+F |
| Number of Dots | 480*3(RGB)*800 |
| Viewing Direction | ALL |
| Module size | 66.26(W)*113.9(H)*3.35(T)mm |
| TFT Active area | 56.16(W)*93.6(H)mm |
| Interface | TFT: MIPI CTP:I2C |
| Luminace | 350cd/m2 |
Shenzhen Chenghao Optoelectronic Co.,Ltd
LCD Manufacturers
Mobile Phone :+86-775-27806536
WeChat/Whatsapp :Tina +15919862398
Skype : add@chenghaolcm.com
Email:add@chenghaolcm.com
Enter Your Message
| Shenzhen ChengHao Optoelectronic Co., Ltd. |
| 7th floor, building C5, Hengfeng Industrial City, Hangcheng street, Bao'an District, Shenzhen |
| 86-755-27806536 |
| add@chenghaolcm.com |
